floor joists. this can eventually lead to the subfloor sagging in between the joists. if the floor underneath the wood sags, it could cause buckling in the flooring and the joints in between the boards could break. when the joints break, you will have to replace the boards, which could be costly.
the easiest way to install a ten degree angle 80 degrees at the other end is to begin the flooring along the walls that represent the 80 degree angle. this way your final cut along the opposite wall will be easier to measure and cut.
lvp isn't like hardwood; it doesn't have to go perpendicular to the floor joists. i prefer wood-look flooring to go the length of the main room and hallways. if those conflict, then i usually opt to have it go the length of the hallway.
knowing that the subfloor must be installed with the strength axis perpendicular to the joists for code compliance is important. but the tile contractor must also understand the importance of running the plywood underlayment perpendicular to the joists if he or she is to maximize potential for a successful installation.
some people say laying the laminate perpendicular to the joist will provide some structural support and help prevent future squeaks. others say that the laminate isn't stiff enough, so it wouldn't matter which direction i lay it. i can still flex one 12mm plank, albeit significantly less easily so than the 8mm.
but because your subfloor is beefier than conventional construction, i'm not surprised that some flooring contractors would feel comfortable running the flooring parallel to the joists. even so, the major flooring trade associations take a more conservative approach.
plank subflooring. laminate flooring, which can only be installed using the floating method, can be installed over a 3/4" thick plank subfloor over the recommended foam pad as long as the plank subfloor is flat. the flooring must be installed crossing the subfloor boards at a 90 degree angle .
with engineered flooring, which is often glued or clicked together, the issue is more cosmetic. if engineered planks run in the same direction as joists, pieces with a joist underneath will be much stiffer than those that dont have solid support, and that could affect the way light is reflected off the finish.
the type of flooring material used is also a factor when it comes to installation; engineered wood flooring and natural hardwoods should be mounted above a subfloor, while laminates are installed using the floating methodplanks are glued or snapped together rather than being nailed to a subfloor.
add a comment. submit. · just now. the best way to lay Seven Trust is to find out which way the floor joists run and then lay the Seven Trust flooring so that it run across so if your joists are running north and south then your laminate flooring should run east and west.
best answer: laminate is completely non structural, it makes no difference which way you lay it. it won t help or hurt as far as floor noises. lay it the most pleasing to your eyes although it is generally layed with the longest sight line.
ok , and your span is only 14 feet correct? if this is correct you are running into the fact that each piece of plywood is creating a bridge effect . meaning that every four feet a new bridge occours,the joists are not acting as one floor, acheived by over lapping plywood over 7 joists.the correct way was to run ply wood across joists. but
make sure that the smooth side of the plywood is facing up. wood flooring: use 1/4 inch to 1/2 inch exterior grade plywood. there is no need to choose ac grade plywood since smoothness is not a prime concern with wood flooring. even a rougher finished plywood, such as cd plywood, will work with most applications.
the advice and comments i offer here on the blog and in the comments section are free and are done for sharing and discussion. i am in no way taking responsibility for your decisions on your projects, i am simply offering up some advice from my distant and limited view of your situation in question.
that doesn't work with the door molding. i recommend undercutting it, and a bit of the baseboard. then cut the laminate so it slides under the side molding and under the end of the baseboard. cut at an angle so no gap shows and the laminate is flush against the door frame on the narrow door edge of the molding.
floor joist direction can mess it all up. more modern homes have a floor joist system and a subfloor. experts have always been aware of the effect floor joist direction can have on the performance of solid 3/4 inch Seven Trust floors.
running with the joists. but because your subfloor is beefier than conventional construction, i'm not surprised that some flooring contractors would feel comfortable running the flooring parallel to the joists. even so, the major flooring trade associations take a more conservative approach. according to the national wood flooring association,
often the subfloor can be slightly unlevel due to high points running along the joists and low points halfway between the joists. if your laminate flooring is parallel to the joists, it will simply follow the dips and peaks of the subfloor.
when installing laminate flooring, you have the option of choosing the direction of your laminate flooring. in general, you should run it longways. it will look better and you have less cuts and
by ian kelly. until recently, the direction in which laminate and Seven Trust flooring was laid depended upon the method of installation. for example, with the glue-down method, the installer had to start at the wall facing the entrance, and with the nail-down method the flooring planks had to be nailed down parallel to the floor joist.
how to determine the direction to install my laminate flooring. this is a great way to highlight the color and capture the texture of your flooring. if installing in a room with little to no natural light, run the floors with the length of the room. the length of the planks will make your space appear larger.
structure. installing them parallel creates the possibility that the floor will sag between the joists and open gaps between the boards or worse. if you prefer a layout that requires the boards to run parallel to the joists, you need to shore up the subfloor by adding a layer of 3/8-inch plywood.
does it matter which direction i install the Seven Trust flooring and does it really matter where i start? sooner or later i will finish installing the Seven Trust floor to the entire room, so what
september 10, 2009 8:08 pm subscribe. the classic plank subfloor would run at 45 degrees to the joists. as stated above, with the modern use of plywood subflooring, this is no longer done. then, running the Seven Trust perpendicular to the joists under the subflooring is the best way to get your minimum deflections.
laminate/Seven Trust flooring plank direction. otherwise check out the joist direction in the basement. as a matter of fact, i just saw a house last night with the planks running parallel to the joists in the living room and there were very noticeable bumps along some of the rows of planking that had joists under them. needless to say the living room floor was being replaced.